S. S. Enterprises

Mayapuri, Delhi

GST No. 07FNIPS3445H1ZM

Call 08048964573 87% Response Rate

our range

Concrete Testing Equipments

Pioneers in the industry, we offer slump test apparatus, concrete cube moulds, semi automatic curing tank, proving rings for lab, compression testing machine and l- box apparatus from India.
Slump Test Apparatus

Slump Test Apparatus

Rs 1,850  / PieceGet Best Price
MaterialMild Steel
Usage/ApplicationLaboratory
BrandSS Enterprises
ShapeCone
Slum Cone Base Dia200 mm
Slum Cone Height300 mm
Model NumberSS-CT-3002
Slum Cone Top Dia100 mm
IS 7320 & BS 1881-102 It is used for the determination of the consistency of freshly mixed concrete, where the maximum size of the aggregate does not exceed 38 mm.

Specification: The apparatus consists of one slump cone with handles and foot pieces. The slump cone has internal dimension 200 mm dia at base 100 mm top dia and 300 mm height foot pieces can be fixed to the clamps on the base plate. The base plate has lifting handle for easy transportation. One graduated steel rod 16 mm dia x 600 mm long rounded at both ends and graduated in mm is also supplied.

View Complete details

get quote request a call back
Concrete Cube Moulds

Concrete Cube Moulds

Rs 1,050  / PieceGet Best Price
MaterialMild Steel
Operating ModeMannual
Model Name/NumberSS-CT-3013
ShapeSquare
ColorBlue
BrandSS Enterprises
UsageConstruction
These are available in different sizes and are made according to Indian and British standards . For the metric size cube mould, the faces are machined flat to +/-0.2mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0.01 inched to within 0.01in. All moulds are supplied complete with base plate.

View Complete details

get quote request a call back
Semi Automatic Curing Tank

Semi Automatic Curing Tank

Rs 75,000  / PieceGet Best Price

Minimum Order Quantity: 1 Piece

Automation GradeSemi-Automatic
Materialstainless Steel
BrandSS Enterprises
Usage/ApplicationCuring / Concrete Compaction
Wattage3000 W
Model NoSS-CT-3016
Capacity1000 litres
Size150 mm
Features:
  • 24 Hour cycle from time of mixing.
  • Controlled 35° C or 100° C ± 2° C Curing Temperature for concrete.
  • Controlled 27° C ± 2° C Curing Temperature for grey cement. The tank has been designed to accommodate 150mm / 70.6mm cube moulds up to 36/72 cube mould and fully insulated, complete with a hinged lid, heater, thermostat and re-circulated pump. Provision of two removable racks allowing free circulation of water around each mould. The pump, drain valves and electrical equipment are housed in a compartment located at one end of the tank. The Tank is heated by an immersion heater under normal conditions and refrigeration system for grey cement the temperature is controlled at 35° C  or 100° C ± 2° C / 27° C +2° C, expect for the 15 minutes after immersion of the freshly made specimens. Note: Accelerated curing tank with cooling arrangement is also available of request.

View Complete details

get quote request a call back
Proving Rings for Lab

Proving Rings for Lab

Rs 45,000  / NumberGet Best Price
MaterialSS
BrandSS Enterprises
Usage/ApplicationLaboratory
Model NoSS-CT-3022
Packing TypeBox
Capacity2kn to 3000kn
DisplayAnalog


Specification: The Proving Rings are made of special steel, carefully forged to provide high and stable accuracy, dependability and repeatability. The dial gauge and anvil are mounted on U-brackets clamped to the ring body by set screws. The indicator has a sensitivity of 0.002mm/ div and the deflection is directly proportional to the applied load. The rings are supplied complete with dial gauge and Works Calibration Chart, individually packed in polished wooden boxes. NPL (India) / NCCBM Calibration Certificates can also be arranged for any proving ring at an additional cost. Separate Pair of Loading Pads are provided to suit each proving ring.

Model
Capacity
Proving Ring Model SS-CT-3022
25kgf to 100kgf (1KN)
Proving Ring Model SS-CT-3022 A
200kgf (2KN)
Proving Ring Model SS-CT-3022 B
250kgf (2.5KN)
Proving Ring Model SS-CT-3022 C
1000kgf (10KN)
Proving Ring Model SS-CT-3022 D
2000kgf (20KN)
Proving Ring Model SS-CT-3022 E
2500kgf (25KN)
Proving Ring Model SS-CT-3022 F
3000kgf (30KN)
Proving Ring Model SS-CT-3022 G
5000kgf (50KN)
Proving Ring Model SS-CT-3022 H
100KN (10Tons)
Proving Ring Model SS-CT-3022 I
200KN (20Tons)
Proving Ring Model SS-CT-3022 J
500KN (50Tons)
Proving Ring Model SS-CT-3022K
1000KN (100Tons)
Proving Ring Model SS-CT-3022 L
2000KN (200Tons)

View Complete details

get quote request a call back
Compression Testing Machine

Compression Testing Machine

Rs 32,000  / PieceGet Best Price
Usage/ApplicationCompression Testing Equipment to test cement, brick and concrete
Display TypeAnalog
Capacity1000kn
GaugeMasta
BrandSS Enterprises
MaterialCast Iron
Model NoSS-CT-3021
Concrete is a man-made material, essentially mixed at site. The properties of concrete depend on the properties of its ingredients and their proportion and it is likely to vary from mix to mix. Tests must be conducted, therefore, to ensure that the concrete used is in accordance with design specifications. A frequent test, is the test of compressive strength, in which concrete samples are tested to failure. Compression Testing Machines: SS series Compression Testing Machines are the finest of their types available. Their rugged construction and extreme simplicity makes it possible for even non- technical personnel to operate them with ease and complete dependability. In particular, the portable units, which are small in dimensions, sturdy and light in weight, make quality control testing possible in areas where commercial testing facilities are not available and where the transportation of larger and much heavier machines would be difficult.

SS Compression Testing Machines conform to IS: 14858(2000) and calibrated with an accuracy of ± 1% as per the requirement of 1828(Class1) . It can also be supplied as per BS : 1881 and BS EN 12390. These machines are available in 50kN, 100kN, 500kN, 1000kN, 2000kN, 3000kN & 5000kN Capacities.
Compression Testing Machines Classification :
  • Analogue models.
  • Motorized model gauge type / electronic
  • Digital models with pace rate indicators.
  • Semi-Automatic pace rate controlled
  • Fully Automatic models

Salient Features of CTM’s are:
  • High stability Load Frames 
  • Self-aligning platen assembly.
  • Load Gauges are calibrated in kN against certified Proving Rings, traceable to  NCCBM  Standards
  • Suitable for testing cubes and cylinders of various sizes.
  • Using special platens, bricks can also be tested.
  • Logged data printing facility through a parallel port interface available in digital and micro controller and fully automatic version. 

View Complete details

get quote request a call back
L- Box Apparatus

L- Box Apparatus

Rs 9,500  / UnitGet Best Price
BrandSS Enterprises
Usage/ApplicationLaboratory
MaterialMild Steel
ShapeL Shape
Model Name/NumberSS-CT-3007
EN 12350-9 
The L Shape box is used for determining the passing ability rate of freshly mixed self compacting concrete. The distance between 12 mm diameter bars can be set between 41±1 mm or 59±1 mm. L Shape box is designed for ease of cleaning the vertical and horizontal hoppers.

The L box apparatus is supplied complete with:
  • Filling Hoppe
  • Base

View Complete details

get quote request a call back
Vee Bee Consistometer

Vee Bee Consistometer

Rs 25,000  / PieceGet Best Price
Usage/ApplicationLaboratory
Voltage240 Volt
BrandSS Enterprises
Frequency50 Hz
Size380 mm X 260 mm
MaterialStainless Steel
Model NoSS-CT-3001
IS 1199 & BS EN 12350 The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc.

Specification: The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia and 600 mm long rounded at both ends.

Additional Information:

  • Pay Mode Terms: Other

View Complete details

get quote request a call back
Compaction Factor Apparatus

Compaction Factor Apparatus

Rs 14,500  / PieceGet Best Price
Automation GradeManual
ColorBlue
Surface FinishingPaint Coated
Number Of Buckets3
Model Name/NumberSS-CT-3003
Usage/ApplicationLaboratory
BrandSS Enterprises
MaterialStainless Steel
Diameter16 mm
Length600 mm
IS 1199, 5515. & BS 1881-103 The apparatus is used for determining the workability of fresh concrete provided the maximum size of the aggregate does not exceed 38mm. The test is particularly useful for concrete mixes of very low workability where true slump values are not reliable.

Specification: It consists of two rigid conical hoppers and a cylinder mounted on a rigid metal frame. The lower openings of the hoppers are fitted with hinged trapdoors having a quick release catches. A circular metal plate is provided to cover the top of the cylinder. Supplied complete with one plaster's trowel and one tamping rod, 16 mm dia x 600 mm long, both ends rounded.

View Complete details

get quote request a call back
Concrete Vibrator Table

Concrete Vibrator Table

Rs 28,000  / PieceGet Best Price
Usage/ApplicationConstruction
Power1-2 kw
Model Name/NumberSS-CT-3024
Max Weight140 Kg
MaterialMild Steel
Automation GradeSemi-Automatic
PhaseSingle Phase
Table Dimension1000mm x 1000 mm
Frequency50 Hz
Voltage440 Volt
BrandSS Enterprises

Proper compaction of cement and concrete while casting specimens for compressive or flexural strength testing essential to achieve a better and more consistent mixture. The cement and concrete vibrating table top has stops along its edges to prevent moulds from sliding off the table during operation. The maximum load capacity is 140 kg. The concrete vibrating tables are offered in 3 different table top sizes:

Model
Table Top Size (mm)
Motor
Electrical Supply
SS-CT-3024.A
1000mm x 1000 mm
1 HP
440V, Three Phase, 50 Hz AC Supply
SS-CT-3024 .B
600 mm x 600 mm
1 HP
440V, Three Phase, 50 Hz AC Supply
SS-CT-3024.C
500 mm x 500 mm
1 HP
440V, Three Phase, 50 Hz AC Supply

View Complete details

get quote request a call back
Concrete Cylindrical Mould

Concrete Cylindrical Mould

Rs 4,500  / PieceGet Best Price
Diameter150 -300 mm
ShapeCylindrical
Surface TreatmentPaint Coated
Model Name/NumberSS-CT-3014
BrandSS Enterprises
MaterialMild Steel
Height150 - 600 mm
The moulds is split vertically into two parts. The mean internal diameter in within +/-0.2mm and height is within +/-1mm. The ends are machined to +/-0.05 . The base plate and top plate are machined flat to +/-0.03mm.

View Complete details

get quote request a call back
Tamping Rod Bar

Tamping Rod Bar

Rs 550  / PieceGet Best Price
Usage/ApplicationIndustrial
Model Name/NumberSS-CT-3012
BrandSS Enterprises
Body MaterialSS
Overall Length600 mm
Diameter16 mm
IS 516, ASTM C-29, C-31, C-57, C-138, C-192 AASHTO  T-29 & T-23 
Specification: This is used for compacting concrete into cube moulds. This rod is made of steel it is 16 mm dia., 600 mm in length and rounded at both ends.

View Complete details

get quote request a call back
Mortar Penetrometer for Lab

Mortar Penetrometer for Lab

Rs 8,500  / PieceGet Best Price
Model Name/NumberSS-CT-3010
Type Of Testing MachinesPowder Dynamometer
ColorWhite
Packaging TypeBox
MaterialMild Steel
BrandSS Enterprises
Usage/ApplicationLaboratory
ASTM C-403 It is used for finding out the rate of hardening of mortar sieved from concrete spring and a stem graduated from 0-70 kg x 1 kg. Six interchangeable penetration needles of areas 645, 323, 65 32 and 16 mm sq. is provided. The penetration resistance is measured by the force exerted to penetrate the mortar by 25 mm and is indicated by a sliding ring on the stem, which is graduated. Needle shanks are marked at every 12.5 mm. Supplied complete in a wooden carrying case.

View Complete details

get quote request a call back
Longitudinal Compressor Meter

Longitudinal Compressor Meter

Rs 18,000  / UnitGet Best Price
Usage/ApplicationLaboratory
BrandSS Enterprises
MaterialMild Steel
Model Name/NumberSS-CT-3018
Automation TypeSemi-Automatic
Diameter300 mm
Display TypeAnalog
ASTM C 469 It is designed for finding out the deformation and strains on 150 mm. Diameter and 300 mm high cement and concrete cylinders when subjected to compressive loads.
Specification.Consists of a frame with a bottom ring and a top ring with tightening screws to firmly clamp the compress meter over the cylinder. A dial gauge .002 mm x 5 mm is mounted on the upper ring and the tie of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying case.

View Complete details

get quote request a call back
Concrete Beam Mould

Concrete Beam Mould

Rs 4,000  / PieceGet Best Price
MaterialCast Iron and Mild Steel
Surface TreatmentPowder Coated
BrandSS Enterprises
Length4-6Feet
Thickness10-18mm
Model NoSS-CT-3015
BS 1881-108 For casting, concrete specimen for flexure tests. 
Specification: Made of Cast Iron / Mild Steel. The mould is made of 4 plates assembled together. Each mould is supplied complete with base plate. Faces are machined flat to ± 0.2mm. And finished in size to 0.2mm. 

View Complete details

get quote request a call back
Laboratory Pan Mixer

Laboratory Pan Mixer

Rs 95,000  / PieceGet Best Price
Usage/ApplicationConstruction
Capacity40 Liter
Model Name/NumberSS-CT-3011
ColorBlue
Automation GradeSemi-Automatic
Motor Power2 HP, 960 RPM
Voltage440 V
PhaseThree Phase
Frequency50 Hz
BrandSS Enterprises
Power SourceElectric
Dimension910 x 875 x 1250 mm
The Concrete mixer has been designed for mixing small quantities of concrete used in preparation of concrete cubes, for testing in laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste uniformly & produce a mix of uniform consistency. This in turn gives consistent quality of cubes specimens when casted in the moulds. The Concrete Mixer developed is transportable on wheels. The design of mixing paddles ensures uniform & efficient mixing of cement & aggregates both in dry & wet conditions. This machine is suitable forThe Concrete mixer has been designed for mixing small quantities of concrete used in preparation of concrete cubes, for testing in laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste uniformly & produce a mix of uniform consistency. This in turn gives consistent quality of cubes specimens when casted in the moulds. The Concrete Mixer developed is transportable on wheels. The design of mixing paddles ensures uniform & efficient mixing of cement & aggregates both in dry & wet conditions. This machine is suitable for aggregate size upto 20 mm. The equipment can also be put to use for mixing of any other material in dry / wet conditions. The arrangement helps the operators to access the pan contents conveniently & emptying the mixture after completion of the operation. The drum is driven off the ribbed base. The lid with mixing paddles clears off the top of the drum to provide maximum access to the operator.

Specifications:
  • Mixing Capacity: 40 ltrs. 
  • Overall Dimension : 910 x 875 x 1250 mm 
  • Motor   : 2 HP, 960 RPM
  • Power supply  : 440 V, 50 Hz, 3 phase AC

Features:
  • Portable, compact & easy to operate
  • Adjustable blades
  • Simple to clean & maintain

View Complete details

get quote request a call back
Pocket Concrete Penetrometer

Pocket Concrete Penetrometer

Rs 2,500  / UnitGet Best Price
MaterialMild Steel
BrandSS Enterprises
Usage/ApplicationLaboratory
Scale Value2i s 0-50 kg/cm
Model NoSS-CT-3009
ASTM C-403 For fast evaluation of the initial setting of concrete. It can be used on light weight concrete, special roof deck mixes and concrete additives.
Specification: Consists of a needle having face area 3/10 sq. cm. and graduated at a distance of 25 cm. The needles point is an integral part of barrel which houses a calibrated spring. The spring is confined in a sleeve. The resistance offered by the concrete mortar is shown on the direct reading scale with a marker ring which holds its position when released. Scale range 2i s 0-50 kg/cm when the penetration resistance reaches a value of 23 5kg/cm the concrete is assumed initially set. Supplied complete in carrying case. 

View Complete details

get quote request a call back
Air Entertainment Meter

Air Entertainment Meter

Rs 25,000  / UnitGet Best Price
Usage/ApplicationLaboratory
BrandSS Enterprises
MaterialSS
Model Name/NumberSS-CT-3025
Automation GradeManual
Display TypeAnalog

IS 1199 1959 & BS 1881-106
As entrainment of air in limited percentage improves durability of concrete and very low percentages deteriorate it ,measurement of air entrapped in freshly mixed concrete becomes important. The use of chemical additives to increase work ability of concrete in turn requires an air content check to be made. Air entrainment meters are used to determine air entrained in freshly mixed concrete by pressure method.

Specification:
The apparatus consists of a pressure tight flanged cylindrical measuring bowl of 0.005 cubic meter capacity for maximum size of aggregate 38mm. The bowl is fitted with a removable flanged conical cover assembly with the help of a seal. The conical cover has an air valve and a petcock for bleeding off the water. A transparent cylindrical stand pipe which is graduated in air content is fixed to the conical cover assembly. Pressure is applied to the specimen with the help of a pressure bulb and the pressure is recorded on the pressure gauge which is mounted on the stand pipe. The whole assembly is mounted on a flat base. The instrument is supplied complete with one each following accessories.

Other Size are also available.

  • 0.007 cubic meter capacity for maximum size of aggregates 38mm,
  • 0.01cubic meter capacity for maximum size of aggregate 75mm.
  • 0.1 cubic meter capacity for maximum size of aggregate 150mm.

 

View Complete details

get quote request a call back
Density Of Fresh And Hardened Concrete

Density Of Fresh And Hardened Concrete

Rs 20,500  / UnitGet Best Price
MaterialMild Steel
Usage/ApplicationLabortaory
BrandSS Enterprises
Surface FinishPowder Coated
Height3 Feet
Automation GradeMannual
Model NoSS-CT-3020
The density of both fresh and hardened concrete is of interest to the engineer for numerous reasons including its effect on durability, Strength and resistance to permeability. Hardened concrete density is determined either by simple dimensional checks, followed by weighing and calculation or by weight in air / water buoyancy methods.
Density of Hardened Concrete: The density of hardened concrete specimens such as cubes and cylinders can be quickly and accurately determined using a Buoyancy Balance.
Buoyancy Balance: The buoyancy balance system developed by us consists of a rigid support frame. Incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance fixed on a cradle. The balance supplied may also be used as a standard weighting device, thus providing a versatile and comprehensive weighing system in the laboratory. The sample is weighed in air and in water to calculate the density of fresh concrete.

View Complete details

get quote request a call back
Lab Concrete Mixer (Motorized)

Lab Concrete Mixer (Motorized)

Rs 35,000  / PieceGet Best Price
Motor Power1/2 HP
Drum Capacity110 L
Drum TypeRound
MaterialMild Steel
Automation GradeSemi-Automatic
Usage/ApplicationConstruction
Power SourceElectric Engine
Model Name/NumberSS-CT-3023
Voltage220 V
PhaseSingle Phase

The Laboratory Concrete Mixer is used for preparing Mix Design of Concrete. It consists of a steel vessel of 55/ 110 Litres capacity, mounted on a frame. The vessel is rotated at 20-22 RPM with the help of a motor and a pulley arrangement. The vessel of laboratory concrete mixer can be titled to any angle by a hand wheel and counter weight. This facilitates mixing and discharge. Blades are provided inside the vessel to mix the material thoroughly. The large pulley wheel facilitates manual rotation of the drum during power failure. The drum, pulley wheel, and motor, etc, are mounted on a steel frame in this laboratory concrete mixer. The concrete mixer is fitted with A 1/2 HP motor. Suitable for Operation on 220V, Single Phase, 50Hz, AC Supply

View Complete details

get quote request a call back
J Ring Apparatus

J Ring Apparatus

Rs 7,500  / PieceGet Best Price
Usage/ApplicationLaboratory
MaterialStainless Steel
BrandSS Enterprises
Height300 mm
Top Diameter100 mm
Base Diameter200 mm
Plate ShapeSquare
EN 12350-12 The J-Ring test is used for determining the passing ability, the flow spread and the flow time of self compacting concrete as the concrete flows through the JRing apparatus. The J-Ring narrow gap with ø18 mm x 16 smooth bars is manufactured from stainless steel. The Slump Cone is made from sheet steel protected against corrosion, with diameters; top 100 mm, base 200 mm and with a height of 300 mm. The Base plate is 900x900x3 mm square, made of stainless steel with engraved circles of 200 mm and 500 mm diameter conforming to EN 123508. The Steel weighted collar is used to stabilize the slump cone on J-Ring or slump flow tests. Minimum apparatus for the J-Ring test are J-Ring with narrow gap and slump cone.

View Complete details

get quote request a call back
Lateral Extensometer for Lab

Lateral Extensometer for Lab

Rs 20,000  / UnitGet Best Price
Usage/ApplicationLaboratory
BrandSS Enterprises
MaterialSS
Model Name/NumberSS-CT-3017
DisplayAnalog
This is for determining the lateral extension of 150 mm dia x 300 mm high cements concrete cylinders while testing them under compression.
Specification: The unit consists of two movable frames pivoted at one end. The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of 0.002 mm x 5 mm is mounted on the upper ring and the tip of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying cast.

View Complete details

get quote request a call back
U Shape Box Apparatus

U Shape Box Apparatus

Rs 9,500  / UnitGet Best Price
Usage/ApplicationLaboratory
BrandSS Enterprises
MaterialSS
Model Name/NumberSS-CT-3008
ShapeU Shape
Automation TypeMannual
The U Shape box apparatus is used to determine the filling and passing ability of self-compacting concrete (SCC). The U box is made of stainless steel consisting of three 12 mm dia. Rebars. The U box is mounted on a frame with a fixing mechanism.

View Complete details

get quote request a call back
V Funnel Apparatus

V Funnel Apparatus

Rs 9,500  / PieceGet Best Price
Usage/ApplicationLaboratory
MaterialMild Steel
Size22.4 mm
BrandSS Enterprises
Model NoSS-CT-3006
EN 12350-9 The V Funnel apparatus is used to evaluate the flow time of freshly mixed self compacting concrete. The test is not suitable when the maximum size of the aggregate exceeds 22.4 mm. The test set consists of a stainless steel funnel placed vertically on a supporting stand. The discharge orifice is equipped with a lid, which can be momentarily opened.
The l shape box apparatus is supplied complete with: 
  • Filling Hopper
  • Base
18

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES